Ad Radar

1986 Honda CRX Si - Crash Diet

Drop those unwanted pounds in no time!

By , Photography by Henry Z. De Kuyper

Most waste little time in pulling the spare tire to drop a few pounds. Others delete their rear interior completely. Then there's Jorge Hurtado, of San Antonio, Texas, and his '86 CRX. Jorge (George to his friends) and his Si are originally from Cali, he states, "I purchased the CRX back in '05 for around $300 in Oxnard... I can't remember how many people made fun of the car, including my friends." The car was indeed rough around the edges, but Jorge loved it more for what it didn't have, namely a few hundred pounds of unnecessary gear found in newer-model cars.

Although the CRX has long been praised for its lightweight chassis, the homely mug of the first-gen was often a put-off for tuners, but that was never the case for Jorge. "An LS-VTEC came together, a paintjob, and wheels. The CRX was fun to drive, and it wasn't that nasty anymore." Jorge had a blast with the little Honda until boost mixed with a missed shift resulted in a blown B series. That's when he got an idea for something bigger. "The H22 was just sitting in my garage, and when I pulled the blown motor, I saw they were roughly the same size, plus I already had a B-series trans." After digging through the Internet and some measurements of his own, Jorge found that the dimensions of the H22 were almost the same as the outgoing B series. He also realized that to his knowledge, an H2B swap had never been shoehorned into an '86 CRX. He recalls, "I purchased a QSD H2B kit and started working on fabricating. Using all of the B-series stuff fits better, and you don't have to cut anything up." Using a custom-designed bracket system and HaSport mounts, he found the swap required no frame modding, and after a few days, the CRX was up and running.

After a couple of passes to dial in the chassis and tire size, the CRX put down a respectable 11.88 on 24-inch slicks. Jorge states, "After that run we drove the car home with the slicks rubbing the shocks and rounded off lug nuts on one wheel...time finally came to give the CRX suspension some attention." The old-school Si was treated to a set of Tokico five-way adjustable shocks and Bilstein 996 coils in the rear. Some much needed corner balance and toe corrections had the suspension dialed in for the new Spinwerkes wheels wrapped in 23-inch M&H slicks. Jorge had already removed most of the easy stuff to save some weight, but with the car down for the suspension changes, he proceeded to pull off a few hundred pounds' worth of extraneous metal. He then went further, and shaved an additional 40 pounds with a custom rear axle. After the crash diet, the svelte CRX tipped the scales at a mere 1,375 pounds!

To take further advantage of the weight loss, upgrades in the power department were next on the list. A set of 450cc DSM injectors added more fuel, while breathing was improved with a custom ported intake manifold and 74mm throttle body. On the hot side, a custom Bisimoto V2 Prototype header was bolted on, and 225 hp at the wheels was achieved. Known as a weak point on most H-series engines, the timing belt tensioner was something that Jorge was determined to work around. His solution involved using all Honda parts. He adds, "The T-belt tensioner on this engine is actually a B-series tensioner. The two tensioners are the same dimensions, and I customized it to work with my H22. Now it's fully adjustable." The custom B-series piece paired with Bisimoto cam gears gave Jorge far more control over the tuning of the H22; his new setup delivering consistent 11.30-second runs with trap speeds a hair under 120 mph. Very impressive numbers for an H22 sporting bolt-ons and a ton of weight reduction. In the wake of newfound success, his higher trap speeds gave him a new problem in the form of dreaded lift. He states, "The rear of the CRX would lift and sway when I'd release the throttle above 100 mph. I used iPhone cases to create wind cuts in the rear window, and now it stays straight with no movement. It's so much easier to control."

Jorge is treading in uncharted waters with his first-gen CRX, making headway for others to follow in his footsteps. He's not resting on his laurels, though, and plans on stroking this motor in search of 300 naturally aspirated horsepower and consistent 10-second runs. Finding so much success with such a simple recipe thus far, there's little doubt that he'll reach his goal in no time.

Bolts & Washers

QSD H2B kit
H-Car front engine mount bracket
H-Car ported intake manifold
H-Car modified B-series manual tensioner
H-Car modified Civic Type R crank pulley
H-Car ram tube intake
Erick's Racing 74mm throttle body
Kaizenspeed balance shaft delete
Half-core radiator
Walbro 255-lph fuel pump
DSM 450cc injectors
Summit in-line fuel filter
B&M fuel pressure regulator
1-gal. Fuel Cell
Bisimoto V2 Prototype stainless steel header
HaSport B-series engine mounts
B16 Y1 transmission
'95 Integra shifter
Clutch Masters Kevlar clutch disc
Toda flywheel
HaSport axles

Tokico Illumina 5-way shocks
Bilstein rear 996 coilovers
H-Car custom lightweight rear axle

'85 CRX HF brake conversion

Wheels & Tires
Front: 13x8 Spinwerkes 350, 23x8-13 M&H slicks
Rear: 15x4 Spinwerkes 350 rims, 22x3.5-15 M&H slicks

Stock body
Lexan windows

Kirkey race seat
H-Car custom suede-wrapped dash
Takata race harness
MOMO Monte Carlo steering wheel
Extreme weight reduction

Neptune engine management
Neptune RTP datalogger
Neptune RD-1 cluster
Odyssey PC 545 battery

My friends
My family
Everyone at Bisimoto
Guillermo "Mr. GPR Auto"
Seth QSD
JR at Hrtuning

Owner Specs

Daily grind
Everything at H-Car

Favorite sites

Screen name

Building Hondas
8 years

Dream car
My other first-gen

Inspiration for this build
Broken camshaft and many who said it wouldn't be possible

Future builds
J35 '85 CRX


If your car weighs less, you typically won't require as much power. It's true, just look at Jorge and his CRX, weighing in at a scant 1,375 pounds; he only needs 225 hp to run consistent low 11s. Starting with an already light platform is a great first step, and his CRX weighed in at 1,900 pounds right off the showroom floor. Getting the car under 1,500 pounds, however, wasn't an easy task. He added, "We cut off everything including the bumper supports, exhaust hangers, and crash bar. I made a custom rear axle, even downsized the brakes to save weight." Jorge went so far as stripping all the underbody sealant designed to prevent rust, which might sound crazy to some, but living in Texas means there are no worries on that end. After removing everything that wasn't needed, the CRX's current power-to-weight ratio is better than a new 500-horsepower-plus GT-R!

1916 S. Lynx Place
CA  91761
HASport Performance
2849 S. 44th St.
AZ  85040
Enjoyed this Post? Subscribe to our RSS Feed, or use your favorite social media to recommend us to friends and colleagues!
Oro Orito
Oro Orito

yes. yes yes......... Honda 84 / 87 yes....

Evelyn Hernandez
Evelyn Hernandez

hell to the freakin yea!!! =D thing must bee killing people off the line! ;D

Sicklo Roxx
Sicklo Roxx

Anyone''' Has anyone ever seen a H2B daily driver???...that works

H-Car Jorge
H-Car Jorge

1,333 lbs with full tank . Never had overheating issues due to header . Mounts kit will be available soon!!!

Nat To
Nat To


Anthony Whitford
Anthony Whitford

With the header that close to the radiator, the engine probably runs really hot.

Rob Webster
Rob Webster

Cant wait for your mounts H-Car Jorge!!!

Harrison Taylor
Harrison Taylor

Props to H-car. They also built the first automatic H2B,pretty interesting build.

Jason Manuel
Jason Manuel

He doesnt run a hood so the intakes getn plenty of cool air

Paul Matagi-Atera
Paul Matagi-Atera

Faarrkk thats tough bro!!! V-tec just kicked in yo!!! #vtec#all#day

Stephen Springs
Stephen Springs

I've seen the yourube videos Ron Newton. This car is super fast.

Honda Tuning Magazine